Mar 23, 2016 This is a DIY solution from a K+DCAN user, who succeeds in setup Standard Tools 2.12 on Windows 10 x64 (64-bit.) that is never qualified by the BMW Group and is considered an experimental platform. Tools tested with: Windows 10 64-bit Home. K+DCAN cable from China (Warning for bad K+DCAN cable!!!I recommend starting with a fresh Windows 10 installation in order to collect the. Dec 04, 2016 BMW INPA 5.0.6 download – working ok with K+Dcan cable December 4, 2016 uobdii Car Diagnostic Tool, OBD2 Cable 0 BMW INPA 5.0.6 download here, which is tested without issues to work with K+DCAN usb cable with inpa bmw e46 and inpa bmw e90. Interface USB OBD2 for BMW-INPA/Ediabas-K+DCAN allows full diagnostic for BMW FTDI FT232RQ Chipset, high speed data transmission, double K-Line support Read erase errors, Adaptations, Coding, works with INPA, with good perforamance Supports High Speed CAN (500 kbit.
- K+dcan Utility 2.0 Download Full
- K+dcan Utility 2.0 Download For Laptop
- K+dcan Utility 2.0 Download For Mac
Looking for some guidance from the good guys here on the Forum. Recently, I Purchased, Downloaded, and had Installed EC-APPS and EDIBAS. I was advised I would have to purchase a cable and install the software for the cable. Ordered cable from eBay: http://www.ebay.com/itm/381593191753...witem=&vxp=mtr
Received in good order has directions that I can follow but seems to not have a specific file on the Disc provided. I just reached out to the vendor for assistance.
Is there anyone here that is really good with this stuff? I have read forums, looked at downloads, but honestly..... it would be way easier to pay to have this done as it seems much of this is a little too technical for me at the moment. Any suggestions or direction from the members here?
Thank you in Advance!
Derrick
If your cheap BMW INPA K+DCAN USB interface with FTDI chip failed to install drivers or the system prompt cannot locate the drivers. Here is a little write-up on how to fix it.
Disclaimer:
I am using Windows 8.1 system. No sure if it works on yours. You are on your own risk.
I am using Windows 8.1 system. No sure if it works on yours. You are on your own risk.
Pre-installation caution:
Here are the INPA driver & software, free download links. If the driver/software is working, then ignore the next part. Otherwise take a look at the following part for reference.
INPA Driver: http://www.obd2vip.com/download/inpa-driver.zip(Close antivirus software or set your browser to download success)
INPA software: http://www.obd2vip.com/download/inpa-2.zip
Here are the INPA driver & software, free download links. If the driver/software is working, then ignore the next part. Otherwise take a look at the following part for reference.
INPA Driver: http://www.obd2vip.com/download/inpa-driver.zip(Close antivirus software or set your browser to download success)
INPA software: http://www.obd2vip.com/download/inpa-2.zip
Procedure:
1. Open your Device Manager. Control Panel–Hardware & Sound–Device Manager.
2. Connect the INPA K+DCAN cable with computer/PC-Double click
3. Locate USB Serial Converter->DetailsDropdown Menu->Hardware IDs. The PID number is the one you want. Will most likely be 0000.
4. Download CDM v2.08.30
http://www.ftdichip.com/Drivers/CDM/CDM%20v2.08.30%20for%20Windows%208.1.zip
2. Connect the INPA K+DCAN cable with computer/PC-Double click
3. Locate USB Serial Converter->DetailsDropdown Menu->Hardware IDs. The PID number is the one you want. Will most likely be 0000.
4. Download CDM v2.08.30
http://www.ftdichip.com/Drivers/CDM/CDM%20v2.08.30%20for%20Windows%208.1.zip
5. Disable “Driver signature verification” Settings–Change PC Settings–Recovery–Advanced Startup–Restart.
This will restart your PC to Advanced settings. From there: Troubleshoot–Advanced Options–Startup Settings–Restart–F7
This will restart your PC to Advanced settings. From there: Troubleshoot–Advanced Options–Startup Settings–Restart–F7
Follow these picture guides:
Your PC will then restart with signature verification disabled. You are now able to edit the INPA drivers.
Your PC will then restart with signature verification disabled. You are now able to edit the INPA drivers.
6. Unzip the Drivers file that you just downloaded and open up
![K+dcan utility 2.0 download for mac K+dcan utility 2.0 download for mac](/uploads/1/1/8/1/118142442/921563025.jpg)
K+dcan Utility 2.0 Download Full
7. Open ftdibus.inf
8. Replace every PID_6001 with PID_0000 to match your hardware ID. Scan through the whole document. Then save it.
9. Then find ftdiport.inf. Do the same to ftdiport.inf
8. Replace every PID_6001 with PID_0000 to match your hardware ID. Scan through the whole document. Then save it.
9. Then find ftdiport.inf. Do the same to ftdiport.inf
10. Back in your Device Manager double click on your OBDII cable again.
Locate USB Serial Convertor Properties->Driver->Update Driver-> Browse my computer.
Locate your driver and install. You will need to install it for both USB Serial Converter and Ports & COM.
Locate USB Serial Convertor Properties->Driver->Update Driver-> Browse my computer.
Locate your driver and install. You will need to install it for both USB Serial Converter and Ports & COM.
11. Setup INPA cable as normal and run INPA software.
K+dcan Utility 2.0 Download For Laptop
It seems that the white FTDI chip INPA cables have to be manually put into D-CAN mode. This file will take care of that. It is normal for the LED to go out.
http://www.mediafire.com/download/35fnrnd3q3dvf3w/D-CAN.exe
If you put the cable into DCAN mode, the LED goes off, and it says there is no adapter connected. Please connect it to the car and run the DCAN mode.
http://www.mediafire.com/download/35fnrnd3q3dvf3w/D-CAN.exe
If you put the cable into DCAN mode, the LED goes off, and it says there is no adapter connected. Please connect it to the car and run the DCAN mode.